Inga produkter tillagda!

Lägg en produkt i varukorgen så ser det lite roligare ut här ;)

Varukorg 0 kr

Rega Elex-R

Rega förstärkare - Integrerad förstärkare

Rega Elex-R

Lagervara ( skickas direkt från leverantören) (Leveranstid ca 3-5 dagar)
Fri frakt!

Integrerad förstärkare med den finare Rega Fono MM RIAA inbyggt. Fjärrkontroll medföljer.
Elex-R har samma fina förförstärkare som storebror Elicit-R sammt betydligt kraftfullare slutsteg än lillebror Brio-R.
För att få plats med de kraftfulla stereslutsteget på 2x80W i 8Ω har Rega byggt ett fullbräddschassi.
Effektförstärkardelen jobbar med Darlington utgångstransistorer som jobbar om om de vore kopplade i Klass A.

The Elex-R is built to the highest standard and designed to deliver the best possible audio performance whilst remaining simple to use and easy to setup.The Elex-R is built into the full width Rega case with increased heat dissipation, which along with a larger transformer enables the Elex-R to deliver 90 Watts per channel into 6Ω and 72.5 Watts per channel into a design centre rating of 8.

Our time, effort & money have been spent on developing the circuit and construction utilizing the highest specification of components throughout. As part of the design we have included useful features like pre-amplifier output, to enable the new Elex-R amplifier to be used in a wide combination of systems and have avoided superfluous gadgets such as tone controls or a headphone socket as they can obstruct the signal path and degrade the produced sound quality.

The Elex-R has been built to Rega’s extremely high standards of reliability and quality to ensure many years of musical enjoyment. The primary function of an amplifier is to boost and equalize the low level signal generated by a phono cartridge, DAC and CD player or other source component to a level that can drive the loudspeakers. It is vital that the amplifier achieves this whilst minimising distortion, as this would directly affect the music. The distortion level is typically 0.007%; just under the clipping of the output.

The volume control and pre-amplifier used in the Elex-R is designed to overcome the problems associated with the standard arrangement. This design uses a custom chip along with peripheral support IC’s like a microcontroller and a custom made rotary volume control.

The Elex-R uses a combined feedback and passive volume control, where the feedback and input levels are varied to set the required volume level. The level and tracking between the two channels is set by the close tolerance parts in the pre-amplifier circuit and less by the actual potentiometer itself, thus keeping the mismatch of channels due to volume control tracking irregularities to a minimum.As well as keeping tracking irregularities to a minimum, this method also reduces noise and input overload as the control will only ‘use’ the required gain to amplify the signal.This form of volume control is normally only found in professional broadcast environments where accurate low noise control of levels is required.

Specifications

Power Supply Voltage: 230v & 115v
Frequency: 50/60Hz
Power Consumption: 250 Watts
230v Fuse: T3.15AL 20mm
115v Fuse: T5AL 20mm
Dimensions W 430mm x D 320mm x H 80mm
Output power72.5W 8Ω both channels driven - Design centre rating

90W 6Ω both channels driven - Rega speaker impedance rating
113W 4Ω both channels driven
Phono input

Sensitivity (72.5W 8Ω1.7mV (Load 47K in parallel with 220pF)
Maximum input level: 100mV
Line input

Sensitivity (72.5W 8Ω 164mv (Load 30-50K)
Maximum input level: 10v
Tape output

Level: 164mV with rated input
Output impedance: 470
Line output

Level: 625mV with rated input
Output impedance: 600

Modell
Elex-R
Varumärke